Connect the video input connector of a VCR with this connector. Connect system cameras or combination cameras to these BNC connectors. Refer to page 72 for the impor-. These BNC connectors supply video signals looped through the video input connectors.
Refer to page 72 for the important notice about the BNC cables to be used. Connect monitors to these BNC connectors. Connect a VGA monitor with this connector. Connect an external device such as a sensor or a door switch with this D-Sub pin connector. Connect a control switch with this D-Sub pin connector when controlling this unit using an external device, or when controlling an alarm device such as a buzzer or a lamp.
Fix the cables with this cable clamp to prevent disconnection or unstable connections that may cause recording failures or an unstable system. The negative circled numbers indicate the default positions of camera title q, time w and event display e.
Note: The camera title will be displayed with 16 characters 2 lines: 8 characters per line. The position of an event display will be symmetrical to the position where the time is displayed. When the time is displayed at the lower left of the screen, an event display will be displayed at the upper right corner of the screen.
The event display will be displayed differently as follows depending on which event has occurred. COM- : When a command alarm has occurred. TRM- : When a terminal alarm has occurred. Note: Refer to page 49 for further information about event types and event actions. The task bar consists of the main bar w - A , the left bar w - B , and the right bar w - C. Displays the status only on the main bar, and does not display information on the left bar and the right bar.
Note: Mode 2 and Mode 3 are graphic operated. When using the optional extension unit WJ-HDE series , turn on the power of this unit after turning on the power of all extension units. The startup splash image below will be displayed on monitor 2 and the VGA monitor during the system check. When the auto login is off, the login window will be displayed if any button on the front panel of this unit is pressed after the system check. Go to step 3. When the auto login is on, live images will be displayed after the system check.
Refer to page for further information. Rotate the jog dial to select a character to be entered in the cursor position. Use the same method to enter or edit characters attached to images.
Refer to page 59 for further information. It is recommended to change the password for an administrator periodically. If the authentication login window is displayed, enter the user name and password. When not authenticated, the authentication login window will be displayed again.
It is recommended to check the clock periodically and put the clock right if it shows the wrong time. When recording is being performed, press the REC button for 2 or more seconds. Recording will stop and the indicator on the REC button will go off. When playback is being performed, press the STOP button. Refer to a system administrator about the required settings for manual recording.
The indicator on the button will light and recording will start. Images from all the connected cameras will be recorded with the default setting. It is possible to record only images displayed on monitor 2 and the VGA monitor by changing the settings. When recording with higher priority than manual recording is performed, manual recording will not be performed until this recording finishes. When the supply of the video input signals to the camera channel is resumed, manual recording will be performed automatically.
Start recording manually using an external switch at an emergency event occurrence. Emergency recording is the highest priority. Refer to a system administrator about the settings. For example, install an external switch at the reception counter, and start recording with it when a suspicious individual appears.
Refer to a system administrator about the required settings for emergency recording. Emergency recording will be performed even when this unit is recording in other recording modes. When the recording duration set in advance has passed, recording will stop automatically.
With the default setting, recording will stop automatically after recording for 10 seconds. Recording duration of emergency recording can be set as follows. Refer to a system administrator for further information. Go to step 2 if not necessary. The pressed camera selection button will light green or blue and the respective live images will be displayed. First playback after login: The latest recorded image will be played. With the default setting, playback will start 5 seconds before the start time of the latest recorded image.
The start time can be selected from the following:. Other than those above: Playback will start from the end point of the recorded image played last time. Rotating the jog dial during playback will skip to the next or previous recorded image. Rotating the jog dial clockwise will skip to the start time of the next recording and start playback, and rotating it counterclockwise will skip to the start time of the previous one.
Rotating the jog dial counterclockwise at a point shortly after the start time of the recording will skip to the start time of the previous recording.
If there is no next or previous recorded image, current playback will continue. Camera selection button 1: 4-split screen Camera selection button 2: 7-split screen Camera selection button 3: 9-split screen. Time of point A.
Playback between point A and B will start and keep playing repeatedly. The time of point A and B will be displayed during playback. Time of point A and B. Note: When the clock of the unit has been changed by editing the time and date settings or by the auto time adjustment function, overlapping of the time ranges of the images recorded before and after the time adjustment could occur.
This is a normal operation. Note: External recording devices can be used as a copy area for images recorded on the hard disk. It is impossible to record images on the external recording devices directly. Recording area in the built-in hard disk of this unit. Recorded images by manual recording page 20 or event recording will be stored in this area. There are 3 ways to search for a recorded image and play it when "HDD normal area" or "event recording area" is selected as the recording area.
Recorded images will be copied in this area. There are 2 ways to search for a recorded image and play it when "HDD copy area" is selected as the recording area.
COPY 1. COPY 2. Press the SET button to determine the selection. Refer to page 28 for further information about the recording event list window. Refer to page 32 for further information about the copy data list window. It is possible to play recorded images from a designated time and date without stopping recording.
The time and date designation window will be displayed on monitor 2 and the VGA monitor. Select the time and date using the jog dial. To move the cursor, use the arrows button A B.
When there are images recorded after the entered time, the oldest recorded image after the entered time will be played. When there are no images recorded after the entered time, the newest recorded image before the entered time will be played. Note: Playback images will be displayed on a single screen on monitor 2 and the VGA monitor. To play in a multi-screen, switch to a multi-screen after starting playback.
Display a list or a thumbnail of recording events, and select the desired recording event from them to play it. It is possible to search using the following filters:. The camera channel of the recorded image will be displayed. The recorded image of. The first several characters of text information will be displayed if the image has text.
The search filter will be displayed. A filter of the currently displayed list will be dis-. Number of the listed data. The recorded image of the displayed camera channel will be played on a single screen. The recording mode also will be displayed. Number of the listed data: The number of the listed data will be displayed. In this case, the thumbnail display may not function properly. The recording event list window will be displayed on monitor 2 and the VGA monitor.
Use the arrows button C D to switch between displaying the list window and the thumbnail window alternately. When a search filter is selected, the respective search filter window will be displayed. Move the cursor using the arrows button and rotate the jog dial to enter the time and date.
Note: When operating the system controller, select a camera channel using the numeric keypad. In this case, it is impossible to select 10 CH to 16 CH. Move the cursor to select the recording event refer to page 28 using the arrows button C D and rotate the jog dial to ON. When events occurred successively, the contents of the event log and the recording event list will not always match since the unit continues to record the first occurring event.
Display a list or a thumbnail of copied recorded images Copy Data , and select the desired copy data file from them to play it.
The time when recording of the source of the copied recorded images had started will be displayed. The camera channel of the copy data file will be displayed.
Camera channel. Starts recording. To stop recording, press this button down for 2 seconds or more. Displays the setup menu, or turns back to the previous page of the setup menu, etc.
Lights when the selected camera was not available to operate because another user is operating it using a controller or a PC via a network. In this case, wait until this indicator goes off. Connect the S-video input connector of a VTR with this connector. Connect the video input connector of a VTR with this connector.
Connect system cameras or combination cameras to these BNC connectors. Refer to page 73 for the impor-. These BNC connectors supply video signals looped through the video input connectors. Refer to page 73 for the important notice about the BNC cables to be used. Connect monitors to these BNC connectors. Connect a VGA monitor with this connector. Some VGA monitors in Europe may not support this refresh rate and could be damaged. Please check the refresh rate supported by your VGA monitor before connecting.
Please check the documentation supplied with your monitor to see if your VGA monitor supports a refresh rate of 50 Hz. Connect an external device such as a sensor or a door switch with this D-Sub pin connector. Connect a control switch with this D-Sub pin connector when controlling this unit using an external device, or when controlling an alarm device such as a buzzer or a lamp.
Fix the cables with this cable clamp to prevent disconnection or unstable connections that may cause recording failures or an unstable system. The negative circled numbers indicate the default positions of camera title q, time w and event display e. Note: The camera title will be displayed with 16 characters 2 lines: 8 characters per line.
The position of an event display will be symmetrical to the position where the time is displayed. When the time is displayed at the lower left of the screen, an event display will be displayed at the upper right corner of the screen. The event display will be displayed differently as follows depending on which event has occurred. COM- : When a command alarm has occurred.
TRM- : When a terminal alarm has occurred. Note: Refer to page 50 for further information about event types and event actions. Some VGA monitors in Europe cannot be used simultaneously with television display. When you enable television display in Europe, the refresh rate for the monitor and television is set to 50 Hz. Some VGA monitors may not support this refresh rate and could be damaged. The task bar consists of the main bar w - A , the left bar w - B , and the right bar w - C.
Displays the status only on the main bar, and does not display information on the left bar and the right bar. Note: Mode 2 and Mode 3 are graphic operated. When using the optional extension unit WJ-HDE series , turn on the power of this unit after turning on the power of all extension units. The startup splash image below will be displayed on monitor 2 and the VGA monitor during the system check. When the auto login is off, the login window will be displayed if any button on the front panel of this unit is pressed after the system check.
Go to step 3. When the auto login is on, live images will be displayed after the system check. Refer to page for further information. Rotate the jog dial to select a character to be entered in the cursor position.
Use the same method to enter or edit characters attached to images. Refer to page 60 for further information. It is recommended to change the password for an administrator periodically. If the authentication login window is displayed, enter the user name and password. When not authenticated, the authentication login window will be displayed again.
It is recommended to check the clock periodically and put the clock right if it shows the wrong time. When recording is being performed, press the REC button for 2 or more seconds. Recording will stop and the indicator on the REC button will go off. When playback is being performed, press the STOP button. Refer to a system administrator about the required settings for manual recording. The indicator on the button will light and recording will start.
Images from all the connected cameras will be recorded with the default setting. It is possible to record only images displayed on monitor 2 and the VGA monitor by changing the settings. When recording with higher priority than manual recording is performed, manual recording will not be performed until this recording finishes. When the supply of the video input signals to the camera channel is resumed, manual recording will be performed automatically.
Start recording manually using an external switch at an emergency event occurrence. Emergency recording is the highest priority. Refer to a system administrator about the settings. For example, install an external switch at the reception counter, and start recording with it when a suspicious individual appears.
Refer to a system administrator about the required settings for emergency recording. Emergency recording will be performed even when this unit is recording in other recording modes. When the recording duration set in advance has passed, recording will stop automatically. With the default setting, recording will stop automatically after recording for 10 seconds. Recording duration of emergency recording can be set as follows. Refer to a system administrator for further information.
Go to step 2 if not necessary. The pressed camera selection button will light green or blue and the respective live images will be displayed.
First playback after login: The latest recorded image will be played. With the default setting, playback will start 5 seconds before the start time of the latest recorded image. The start time can be selected from the following:. Other than those above: Playback will start from the end point of the recorded image played last time. Rotating the jog dial during playback will skip to the next or previous recorded image.
Rotating the jog dial clockwise will skip to the start time of the next recording and start playback, and rotating it counterclockwise will skip to the start time of the previous one. Rotating the jog dial counterclockwise at a point shortly after the start time of the recording will skip to the start time of the previous recording. If there is no next or previous recorded image, current playback will continue.
Camera selection button 1: 4-split screen Camera selection button 2: 7-split screen Camera selection button 3: 9-split screen. Time of point A. Playback between point A and B will start and keep playing repeatedly. The time of point A and B will be displayed during playback. Time of point A and B. Note: When the clock of the unit has been changed by editing the time and date settings or by the auto time adjustment function, overlapping of the time ranges of the images recorded before and after the time adjustment could occur.
This is a normal operation. Note: External recording devices can be used as a copy area for images recorded on the hard disk. It is impossible to record images on the external recording devices directly.
Recording area in the built-in hard disk of this unit. Recorded images by manual recording page 21 or event recording will be stored in this area. There are 3 ways to search for a recorded image and play it when "HDD normal area" or "event recording area" is selected as the recording area.
Recorded images will be copied in this area. There are 2 ways to search for a recorded image and play it when "HDD copy area" is selected as the recording area. COPY 1. COPY 2. Press the SET button to determine the selection. Refer to page 29 for further information about the recording event list window. Refer to page 33 for further information about the copy data list window. It is possible to play recorded images from a designated time and date without stopping recording.
The time and date designation window will be displayed on monitor 2 and the VGA monitor. Select the time and date using the jog dial. To move the cursor, use the arrows button A B. When there are images recorded after the entered time, the oldest recorded image after the entered time will be played. When there are no images recorded after the entered time, the newest recorded image before the entered time will be played.
Note: Playback images will be displayed on a single screen on monitor 2 and the VGA monitor. To play in a multi-screen, switch to a multi-screen after starting playback. Display a list or a thumbnail of recording events, and select the desired recording event from them to play it. It is possible to search using the following filters:. The camera channel of the recorded image will be displayed.
The recorded image of. The first several characters of text information will be displayed if the image has text. The search filter will be displayed. A filter of the currently displayed list will be dis-.
Number of the listed data. The recorded image of the displayed camera channel will be played on a single screen. The recording mode also will be displayed. Number of the listed data: The number of the listed data will be displayed.
In this case, the thumbnail display may not function properly. The recording event list window will be displayed on monitor 2 and the VGA monitor. Use the arrows button C D to switch between displaying the list window and the thumbnail window alternately. When a search filter is selected, the respective search filter window will be displayed. Move the cursor using the arrows button and rotate the jog dial to enter the time and date. Lights when a selected camera was not available to operate because another user is operating it using a controller or a PC via a network.
In this case, wait until this indicator goes off. Connect the S-video input connector of a VTR with this connector. Connect the video input connector of a VTR with this connector. These BNC connectors supply video signals looped through the video input connectors. Connect a VGA monitor with this connector. Some VGA monitors in Europe cannot be used simultaneously with television display.
When you enable television display in Europe, the refresh rate for the monitor and television is set to 50 Hz. Some VGA monitors may not support this refresh rate and could be damaged. Please check the documentation supplied with your monitor to see if your VGA monitor supports a refresh rate of 50 Hz. Connect an external device such as a sensor or a door switch with this D-Sub pin connector.
Connect a control switch with this D-Sub pin connector when controlling this unit using an external device, or when controlling an alarm device such as a buzzer or a lamp. Note: The camera title will be displayed with 16 characters 2 lines: 8 characters per line.
Note: When the camera title and the time display are layered, only the time display will be displayed. The alarm display will be displayed differently as follows depending on which alarm has occurred. COM- : When a command alarm has occurred. TRM- : When a terminal alarm has occurred.
Note: Refer to page 44 for further information about event types and event actions. When you enable television display in Europe, the refresh rate for the monitor and television is set to 50Hz.
The task bar consists of the main bar w - A , the left bar w - B , and the right bar w - C. Displays the status only on the main bar, and does not display information on the left bar and the right bar.
Note: Mode 2 and Mode 3 are graphic images. Note: Refer to page 55 for further information about error types and what to do when an error has occurred. The startup splash image below will be displayed on monitor 2 and the VGA monitor during the system check. When the auto login is off, the login window will be displayed if any button on the front panel of this unit is pressed after the system check. Go to step 3. When the auto login is on, live images will be displayed after the system check.
Refer to page for further information. When using the optional extension unit WJ-HDE , turn the power of this unit after turning on the power of all extension units.
Rotate the jog dial to select a character to be entered in the cursor position. Use the same method to enter or edit characters attached to images. Refer to page 53 for further information. It is recommended to change the password for an administrator periodically.
If the authentication login window is displayed, enter user name and password. When not authenticated, the authentication login window will be displayed again.
It is recommended to check the clock periodically and put the clock right if it shows the wrong time. When recording is being performed, press the REC button for 2 or more seconds. Recording will stop and the indicator on the REC button will go off. When playback is being performed, press the STOP button. Refer to a system administrator about the required settings for manual recording. The indicator on the button will light and recording will start.
Images from all the connected cameras will be recorded with the default setting. It is possible to record only images displayed on monitor 2 and the VGA monitor by changing the settings. When recording with higher priority than manual recording is performed, manual recording will not be performed until this recording finishes. Start recording manually using an external switch at an emergency event occurrence. Emergency recording is the highest priority. Refer to a system administrator about the settings.
Approximate possible recording durations will be as follows with built-in HDD, manual recording :. The possible recording durations on the above tables are approximate durations under the conditions below. The possible recording durations varies depending on object of shooting. Refer to a system administrator for further information. For example, install an external switch at the reception counter, and start recording with it when a suspicious individual appears.
Refer to a system administrator about the required settings for emergency recording. Emergency recording will be performed even when this unit is recording in other recording modes. When the recording duration set in advance has passed, recording will stop automatically.
With the default setting, recording will stop automatically after recording for 10 seconds. Recording duration of emergency recording can be set as follows. Go to step 2 if not necessary. The pressed camera selection button will light green or blue and the respective live images will be displayed. First playback after login: The latest recorded image will be played.
With the default setting, playback will start 5 seconds before the start time of the latest recorded image. The start time can be selected from the following:. Other than those above: Playback will start from the end point of the recorded image played last time.
Rotating the jog dial during playback will skip to the next or previous recorded image. Rotating the jog dial clockwise will skip to the start time of the next recording and start playback, and rotating it counterclockwise will skip to the start time of the previous one. Rotating the jog dial counterclockwise at the point around the start time of the recording will skip to the start time of two more previous recording. If there is no next or previous recorded image, current playback will continue.
Camera selection button 1: 4-split screen Camera selection button 2: 7-split screen Camera selection button 3: 9-split screen. It is possible to display text information attached to recorded image while playback. Text display is available only when playing on a single screen. Time of point A. Time of point A and B. Note: Playback will be paused if the playback time caught up with the recording time present time when recording and playback are performed simultaneously. Note: External recording devices can be used as a copy area for images recorded on the hard disk.
It is impossible to record images on the external recording devices directly. Disk space for recording on the built-in hard disk Recorded images by manual recording refer to page 18 or event recording will be stored in this area.
Press the SET button to determine the selection. The recording event list window will be displayed. Refer to page 27 for further information. It is possible to play recorded images from a designated time and date without stopping recording.
The time and date designation window will be displayed on monitor 2 and the VGA monitor. Select time and date using the jog dial.
To move the cursor, use the arrows button AB. When there are images recorded after the entered time, the oldest recorded image after the entered time will be played. When there are no images recorded after the entered time, the newest recorded image before the entered time will be played.
Note: Playback images will be displayed on a single screen on monitor 2 and the VGA monitor. To play in a multi-screen, switch to a multi-screen after starting playback. Display a list or a thumbnail of recording events, and select the desired recording event from them to play it. It is possible to search using the following filters:. Camera channel of the recorded image will be displayed.
The recorded image of the. First several characters of text information will be displayed if the image has text infor-. Searching filter will be displayed. A filter of the currently displayed list will be displayed. Number of listed data. The recorded image of the displayed camera channel will be played on a single screen. Recording mode also will be displayed. Number of the listed data: Number of the listed data will be displayed.
Note: Some images displayed in the thumbnail window may not match with respective displayed recorded time. The recording event list window will be displayed on monitor 2 and the VGA monitor. Use the arrows button C D to switch displaying the list window and the thumbnail window alternately.
When a searching filter is selected, the respective searching filter window will be displayed. Move the cursor using the arrows button and rotate the jog dial to enter time and date. Note: When operating the system controller, select a camera channel using the numeric keypad. In this case, it is impossible to select 10 CH to 16 CH.
Move the cursor to select the recording event refer to page 27 using the arrows button CD and rotate the jog dial to ON. When events occurred successively, contents of the event log and the recording event list will not always match since the unit continues to record the first occurred event.
Search for a motion detected time and date from all images recorded in all the recording modes, and display a list or a thumbnail of the results. It is possible to filter by camera channel, time and date, detection area or searching mode, to list time and date of events that were recorded when motion was detected. In case recording is being performed, press the REC button for 2 or more seconds. Recording will stop and the indicator on the REC button will go off.
In case playback is being performed, press the STOP button. Refer to a system administrator about the required settings for manual recording. Refer to a system administrator for further information.
For example, install an external switch at the reception counter, and start recording using it when a suspicious individual appears. Refer to a system administrator about the required settings for emergency recording. Playback image will be displayed on the monitor 2 and the VGA monitor. Camera selection button 1: 4 split screen Page 24 A - B repeat playback It is possible to play recorded images between two designated points repeatedly.
Available disk space or disks are as follows. Note: External recording devices can be used as copy area of images recorded on the hard disk. Page 27 Playback From a Designated Time and Date It is possible to play recorded image from a designated time and date without stopping recording. The selected camera channels will be highlighted white. Page 32 Searching a motion detected time and date from recorded images and play it VMD search Search a motion detected time and date from all images recorded in all the recording modes, and display a list or a thumbnail of the results.
Select a time and date displayed on the result list or thumb- nail to play it. Page 34 , Rotate the jog dial to select "EXIT" on the status bar to exit from the motion detection area setup window. Refer to page xx for further information about each of the detection mode. Live image will be displayed on the monitor 2 and the VGA monitor. Detection Mode Set how to detect motion in the set motion detection area. There are 3 detection modes as follows: Important It is impossible to set two or more detection modes simulta Page 36 Searching a marked point and play from that point Marking search Display the recording time of recorded images with a marked point in a list or a thumbnail and select the desired recording time to play.
Refer to page XX for further informa- tion about marking. Live image from the selected camera will be displayed and the respective camera selection button will light green or blue. Pressed button number will be registered as a preset posi- tion number.
The jog dial also can be used to select a preset position number by rotating it. Page Cancel The Alarm Action Cancel the Alarm Action When an alarm occurred, this unit will start the alarm action according to the selected alarm action mode. It is recommended to make back-up copies on a regular basis for unexpected situations such as malfunction of the hard disk.
Refer to a system administrator for further information about the other disks. Important All data on the disk will be deleted if formatted initialized. The confirmation window will be displayed. During formatting, the status window will be displayed. The status window will be closed automatically when com- pleting formatting. Entering 20 characters for a line up to 10 lines, with a total of characters for text information is possible. The available features and the system requirements of a PC are as follows.
Remove the rubber legs 6 pcs. Install the rack mounting brackets on both sides of the unit. Page 61 v Enter a user name and password. Refer to page XX for further information about the user name and password.
The HDD safety mode will begin.
0コメント